ARGON D2C CHIP : New 9 Wire Argon Firmware available: DMS - D2A - D2B - D2C
WASABUS - 9 Wire Bios - CONFIRMED VERSION -
It is a 9 wires modchip and without any program in it, whatever program you put in -
it will work this programm. It is powerful!!!
Code injected in the controller is the same like wasabi, is tested in this version only on WII D2C versions.
ARGON SPI we will add the support of old DMS versions.
Be careful, the diagram is little changed, the U point is different than first diagram, pls. note this!
Kindly to advise you that our 9 wires argon - WASABUS ARGON SPI - Released.
INFECTUS TEAM - ARGON SPI - 9 WIRES FIRMWARE RELEASE
FIRMWARE ONLY FOR ARGON WITH ACTEL A3P250 and A3P125"
the version A3P125 is also available !!!!
http://www.infectus.biz/forum/index.php?topic=1768.0
In this ZIP fill you will find these things:
1- INFECTUS PROGRAMMER, beta version to manage correctly
ARGON SPI update
2- wasabus_argon.bin, this is the firwmare that is necessary
to flash inside the SPI flash of ARGON
3- wasabus_a.dat, this is the new ACTEL firmware to support
9 wires installation
Procedure to upgrade ARGON SPI with new WASABUS FIRMWARE 9
WIRES:
1- Install the new programmer (use the DLL of the official
version
2- TOOLS > OPEN INFECTUS load the "wasabus_a.dat" and
program the ARGON like other firmwares
3- EXIT FROM "OPEN INFECTUS" MENU
4- DISCONNECT THE INJECTUS PROGRAMMER FROM USB AND RECONNECT
5- ON THE BOTTOM RIGHT CORNER THE PROGRAMMER WILL SHOW THE
SPI FLASH ID (is very important that there is the PART NO.
PM25LV020)
6- GO TO MENU "FLASH COMMAND" > SELECT ERASE and than WRITE
(select the file wasabus_argon.bin) and wait the flashing
procedure.
WASABUS debug LEDS:
The LED on the ARGON will show you if modchip is correctly
working or not, is very simple
LED OFF = Don't works
LED ON = Code injection procedure is complete
REGIONAL SETUP:
Current firmware is setup by default like PAL, and in the
next revision we will use two ARGON pads to configure the
regional version.
NEW COOL FEATURE WITH INJECTUS CONNECTED:
The new firmware allow the users to leave INJECTUS
PROGRAMMER connected to the modchip and use the SWITCHES and
LED to understand the modchip status.
Pls. remove the USB cable from PC when you use INJECTUS to
configure ARGON and check ARGON STATUS.
When argon is correctly working the INJECTUS will show GREEN
LED ON, if the LED IS RED, the modchip is OFF.
The switch allow to configure regional configuration or
switch off the modchip the combinations are:
Switch 1 = Off
Switch 2 = Off >>> PAL firmware
Switch 1 = On
Switch 2 = On >>> Modchip disabled
Switch 1 = On
Switch 2 = Off >>> JAP firmware
Switch 1 = Off
Switch 2 = On >>> USA firmware
Infectus has released the newest Wii mod chip Argon which works on all Wii D2C Drive boards this chip has only 13 wires + 4 extra wires optional - to install and is flash upgradable. The Argon Bios works on Australian USA European and Japanese Wii Consoles. A high quality solution for your Wii console. Argon Install diagrams here
Argon D2C mod chips latest bios is 1.8 and has excellent media compatibility ( best of current D2C Modchips for wii ) The
D2C Pro - Wii mod chip now available - One of the Latest of the D2C modchips for Wii Console - All Region and comes with "Easy Board" installation connector to make installing the D2C Pro a Breeze. D2C Pro is very similiar to D2CKey but has a Disarmable mode - which is one extra wire during installation. D2C Pro Installation diagrams here
D2CKey - Wii mod chip now available - The First of the D2C modchips for Wii Console - All Region Wii Mod chip for all D2C chipsets. D2CKey is 32 wire installation -. D2CKey Installation diagrams here
WiiKey Gold Mod chips Genuine with Hologram AU 11 / Wiikey Platinum XT AU 35
